608 Results
View Results:
Sort by:
FE Mesh Refinement Factor for Reducing Calculation Time
How can I reduce the calculation time for members with a nonlinear material model in RFEM 6 and RSTAB 9?
Meaning of location_flags of Class members_internal_forces (WebService API)
What is the meaning of the location_flags in the members_internal_forces class of the WebService API?
Different Stresses in Static Analysis and Stress-Strain Analysis
Why are the stresses of the structural analysis different from those calculated with the Stress-Strain Analysis add-on?
Stability Analysis of Structural Components with Asymmetric Cross-Section
Is it possible to use the general method according to EN 1993‑1‑1, 6.3.4 to design structural components with an asymmetric cross-section in the Steel Design add-on for RFEM 6 or RSTAB 9?
Reinforced Concrete Design of Solids
Is it possible to use the add-ons for RFEM 6 to design concrete solids?
Add-ons for Timber Structures
Which Dlubal software products do you recommend for the structural analysis and design of timber structures in particular?
Result Selection for Design Situation / Result Combination
Why are the maximum deformations not displayed?
Stability Analysis with Torsion
When performing steel design in RFEM 6 or RSTAB 9, I get a warning that the torsion is neglected in the stability design checks. What is the reason for this, and how can I get around the warning message?
Importing Surfaces from Rhino into RFEM 6
Why are not all surfaces transferred when importing surfaces from Rhino into RFEM 6?
Interface RFEM 6 / RSTAB 9 – IDEA StatiCa
How can I exchange data between RFEM 6 / RSTAB 9 and IDEA StatiCa?
Add-ons for Concrete Structures
Which products do you recommend for the structural analysis and design of reinforced concrete structures?
Add-ons for Steel Structures
I process steel structures. Which products do you recommend for this area?
Performance Problems on Modern Intel Processors
RFEM calculates more slowly on my new computer than on the old one. What might be the cause, and how can I change it?
Load Transfer Surfaces
The loads from the load transfer surfaces are not displayed. Where are they?
Saving Toolbars
I have customized my toolbars. How can I save these settings to use them on another computer?
Unit Stresses
Can I estimate which minimum cross-sections I should use before starting to design my model?
Member Nonlinearity
Is it possible to define member nonlinearities for beam members?
For example, can I define a member that absorbs all internal forces, except for the compressive axial forces?
Pipe as Shear Key in RF-/JOINTS Steel – Column Base Add-on Module
How do I define a pipe as a shear key in RF‑/JOINTS Steel – Column Base add-on module?
Is it possible to avoid the login when starting the programs RFEM 6 and RSTAB 9?
Is it possible to avoid the login when starting the programs RFEM 6 and RSTAB 9?
RWIND Calculation Error E315
When performing high-quality transient simulations with a high number of mesh cells, I get this error: "Calculation failed! RWindSolverTransient failed, E315." After that, RWIND stops without results. What can I do?
Steady-State or Transient Simulation for Parapet in RWIND
What is the most accurate CFD method for the wind simulation of parapets?
Effective Section
Can I calculate the effective section properties of a cross-section using RSECTION?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM